Prev: Soapbox-derby style trike
Next: A Reeky clubhouse IRL
From: Lee K. Gleason on 14 Nov 2009 16:58 My 77 RD-400 needs new crank seals. I have the factory service manual, but its procedures assume a complete teardown is required, and goes into the detail necessary to completely dissasemble engine & trans. I'm wondering if I can get by with substantially less dissasembly. Anyone done one of these lately? Can I split the cases just by removing the bolts in the bottom of the lower case? Any other advice for this project? -- Lee K. Gleason N5ZMR Control-G Consultants lee.gleason(a)comcast.net
From: Nagarjuna's Catuskoti clawed me! on 14 Nov 2009 19:07 On Nov 14, 1:58�pm, "Lee K. Gleason" <lee.glea...(a)comcast.net> wrote: > � I'm wondering if I can get by with substantially less dissasembly. Anyone > done one of these lately? Can I split the cases just by removing the bolts > in the bottom of the lower case? Any other advice for this project? It sounds like you're the guy with a manual and some tools that TOG keeps warning us about... Do actually think that you can pull the crankshaft and pistons out through the bottom? If you could, how would you ever get the piston rings back into the cylinder bores without breaking them?
From: The Older Gentleman on 15 Nov 2009 10:46 Lee K. Gleason <lee.gleason(a)comcast.net> wrote: > My 77 RD-400 needs new crank seals. I have the factory service manual, but > its procedures assume a complete teardown is required, and goes into the > detail necessary to completely dissasemble engine & trans. > > I'm wondering if I can get by with substantially less dissasembly. No >Anyone > done one of these lately? No > Can I split the cases just by removing the bolts > in the bottom of the lower case? Yes, but it won't help. > Any other advice for this project? Hand it over to someone who knows what they're doing, or have them standing by. -- BMW K1100LT Ducati 750SS Honda CB400F Triumph Street Triple Suzuki TS250ER GN250 Damn, back to six bikes! Try Googling before asking a damn silly question. chateau dot murray at idnet dot com
From: S'mee on 15 Nov 2009 13:27 On Nov 15, 8:46 am, totallydeadmail...(a)yahoo.co.uk (The Older Gentleman) wrote: > Lee K. Gleason <lee.glea...(a)comcast.net> wrote: > > > My 77 RD-400 needs new crank seals. I have the factory service manual, but > > its procedures assume a complete teardown is required, and goes into the > > detail necessary to completely dissasemble engine & trans. > > > I'm wondering if I can get by with substantially less dissasembly. > > No > > >Anyone > > done one of these lately? > > No > > > Can I split the cases just by removing the bolts > > in the bottom of the lower case? > > Yes, but it won't help. > > > Any other advice for this project? > > Hand it over to someone who knows what they're doing, or have them > standing by. > Having NOT torn down an RD I'll take for granted your advice is better. 8^)
From: Bill Smith on 15 Nov 2009 13:57
On Sat, 14 Nov 2009 15:58:53 -0600, "Lee K. Gleason" <lee.gleason(a)comcast.net> wrote: > My 77 RD-400 needs new crank seals. I have the factory service manual, but >its procedures assume a complete teardown is required, and goes into the >detail necessary to completely dissasemble engine & trans. > > I'm wondering if I can get by with substantially less dissasembly. Anyone >done one of these lately? Can I split the cases just by removing the bolts >in the bottom of the lower case? Any other advice for this project? Take the clutch cover off and remove the clutch. Behind it you will find a flat ring that's attached to both the upper and lower cases with three screws (this helps axially locate the transmission main shaft bearing), once you remove it (and the alternator along with it's cover, of course) you can split the cases. With both pistons at mid stroke you can lift the crank enough to replace the seals. When you drop the crank back in, make sure that the little locating bumps on the bearings are in the recesses machined for them in the cases along the parting line. This a quick and dirty (literally) way to do it, but I wouldn't recommend it. You must clean all the adhesive off the mating surfaces to insure a leak free assembly, if you don't you could have a lean condition and a piston seizure as a result. This is difficult to do with the transmission and crankshaft in place with a big possibility of crud in both of them after you're finished with the assembly. It doesn't take that long to do it right, these are hammer simple engines to work on. Disassemble it completely, inspect everything as long as you are in there and reassemble it clean, you'll be happier. Doing it right once is much quicker than having to do it twice. Bill Smith |